Some Safari browsers are failing to connect secured pages Try the following: - refresh the page a few time to see if the page loads, if this fails please update the browser or try to browse the page in Firefox or Chrome. - Read more.
Minispares.com uses cookies to give a better browsing experience. Read more 
HPS4

OIL PRESSURE REGULATOR KIT WITH CHROME KNOB

This kit includes a new oil galery plug with an adjustable knob and a washer which is used as a spring seat in the plug against the relief spring. This makes a playform for the adjuster bolt to adjust the engine oil pressure. Winding the knob in increases pressure, winding it out reduces the pressure.







The standard spring 6K853 is easier to use as its compressed length is shorter and softer for fitment. If you have to much oil pressure, or difficulty in fitting, one coil of the spring ca be cut off at a time. Remember that excessive oil pressure can raise oil temperature and absorbs valuable horsepower.







This kit can only adjust the total amount of oil pressure. That figure should be 50-60 psi at anything over 3000 RPM, any more pressure than that is just heating up the oil and wasting power. You cannot affect the idle speed oil pressure with this kit; whatever pressure you have at idle is governed by internal engine clearances, oil temperature, grade and quality.
  • £15.65 exc vat
  • £18.78 inc vat

 In stock

 
help Recommended usage 1 x HPS4 to fit one mini.
 
  • share
 

Recommended products

Showing 1 to 0 of 0 products
OIL PRESSSURE VALVE AND SPRING
6K853KIT   More Details
£3.15
(inc VAT) £3.78

 

This kit contains

Showing 1 to 0 of 0 products
WASHER 5MM M5 PLAIN WASHER FOR HPS4 ETC
GFK1201   More Details
£0.06
(inc VAT) £0.07

NUT PLAIN 1/4" UNF
GFK3211   More Details
£0.07
(inc VAT) £0.08

GRILLE BUTTON KNOB ONLY CHROME (SINGLE)
954-BUT   More Details
£4.55
(inc VAT) £5.46

 

People also bought

Showing 1 to 0 of 0 products
TIMING COVER AND FRONT PLATE FITTING KIT
MSSK063   More Details
£8.00
(inc VAT) £9.60

SWIFTUNE PERFORMANCE DIE CAST PISTON SET 1275......
C-STN103-40   More Details
£255.00
(inc VAT) £306.00

MINI 1275 CAM LINER SET
MS3063   More Details
£15.75
(inc VAT) £18.90

MAINS SET 60 OVERSIZE PRE A PLUS/EARLY A+ 127......
AEM91120-60   More Details
£26.25
(inc VAT) £31.50

CRANK THRUST WASHER SET +0.003" 1275
ACL2136-003   More Details
£11.25
(inc VAT) £13.50

MINI SPARES COMBINED BLOCK/GEARBOX GASKET AND......
AJM100MS   More Details
£26.00
(inc VAT) £31.20

MAINS +10 1275CC A PLUS ONLY ACL RACE
C-AEM91886-10   More Details
£78.62
(inc VAT) £94.34

MAINS STANDARD SIZE 1275CC A PLUS ONLY ACL RA......
C-AEM91886-00   More Details
£78.62
(inc VAT) £94.34

BIG ENDS +10 1300 EXCEPT COOPER S ACL RACE
C-AEB91306-10   More Details
£71.69
(inc VAT) £86.03

BIG ENDS SET 998/1098/970/1071/ COOPER "S" AC......
C-AEB572-00   More Details
£66.27
(inc VAT) £79.52

TIMING CHAIN DUPLEX LIMITED STRETCH TYPE
2H4905EVO   More Details
£19.64
(inc VAT) £23.57

TIMING CHAIN SINGLE ROW SPECIAL QUALITY
3H2127EVO   More Details
£20.88
(inc VAT) £25.06

8° OFFSET WOODRUFF KEY
WKN8OSET   More Details
£10.50
(inc VAT) £12.60

4° OFFSET WOODRUFF KEY
WKN4OSET   More Details
£10.50
(inc VAT) £12.60

2° OFFSET WOODRUFF KEY
WKN2OSET   More Details
£10.50
(inc VAT) £12.60

1° OFFSET WOODRUFF KEY
WKN1OSET   More Details
£10.50
(inc VAT) £12.60

3° OFFSET WOODRUFF KEY
WKN3OSET   More Details
£10.50
(inc VAT) £12.60

NUT FOR 1300 CON ROD AS USED ON C-STR289
C-STR290   More Details
£1.39
(inc VAT) £1.67

PRIMARY GEAR THRUST WASHER 1275CC 122-124 THO......
DAM6492   More Details
£24.00
(inc VAT) £28.80

RIGID ENGINE TO GEARBOX HALF MOON SEAL U
CAM6548   More Details
£4.00
(inc VAT) £4.80

Fitting instructions / Articles

Lubrication - Oil pumps


Essential to the well being of every engine is its oil pump and oil. Much in the same way as the heart and blood is deemed relatively important to us humans! It's also another of those greatly misunderstood and, unfortunately, misrepresented subjects connected to engines.

An alarming number of so-called A-series engine specialists would have you believe that once parting with a veritable bundle of your hard earned readies on that mega motor, what you really need to keep it in good health is a high-pressure/high-flow oil pump. Seems a sensible consideration - except in the A-series world it's impossible. Oh, there are pumps that will give better flow rates than others, but high pressure? Absolutely not.

Oil pressure is regulated by the relief valve in the block of an A-series, not in the oil pump as with say a Ford. Yeah, you know - the one that gets jammed, causing heart failure as you believe your crank bearings have dissolved, and is a pig to get out.